General Information

Important Safety Notes:

• Check the inside of the larger pieces in your box for other materials packed inside.
• When assembling components, place on a non-abrasive surface (i.e. shipping box) to avoid scratching.
• We recommend an area approximately 5’x 8’ for unobstructed assembling.
• You should not need to use excessive force when assembling components.

Returns:
If you wish to return your product, please contact us first — we can often help resolve the issue right away.
If a return is still necessary, it must be initiated with the retailer where the product was purchased.

Need Help or Replacement Parts?

Although great care has been taken to ensure proper packaging and handling of this product, occasional issues can occur.

If you need replacement parts, assembly assistance, or have questions about the product, our customer service team is ready to help:

• Website: https://parts.nychbrands.com
• Email: support@encloscreens.com
• Phone: 704-892-5222 or 877-234-6196

Customer service agents are available 9am–5pm EST, Monday–Friday.

For Quick Assistance:

• Have reference item number EC18027
• Provide the specific part name
• Include the batch lot number found on the end of the box

Detailed Dimensions & Specifications

Product Specifications:

• Panel height: 48in
• Panel width: 40in
• Space between slats: ½ in
• Depth in Ground of Anchor: 12in

A — Left Post (2)

⅞" x 2" x 48"

B — Right Post (2)

⅞" x 2" x 48"

C — Post Anchor (4)

¾" x 1¼" x 15"

D — Rail (4)

⅝" x 1" x 39⅞"

E — Board (8)

⅜" x 10" x 39⅞"

F — Joiner Clip (2)

G — ¾" Self-Drilling Stainless Steel Screw (20)

H — 1½" Self-Drilling Stainless Steel Screw (8)

• Insert (1) Rail (D) into Right Post (B) in the top routed hole.
• Assemble on box or other smooth surface to prevent scratching.

• Insert (1) Board (E) into the Right Post (B) at the top.

• Continue inserting the remaining (3) Boards (E) into the other slots on the Right Post (B).

• Insert (1) Rail (D) into the Right Post (B) in the bottom routed hole.

• Attach Left Post (A) to the panel.
• Ensure pre-drilled holes for the left and right post align.
• For an easier assembly, use a wall as support for the right post.

• Insert (8) ¾" Self-Drilling Stainless Steel Screws (G) into the pre-drilled holes on posts.

• Insert (2) Post Anchors (C) into the bottoms of the posts.

• Insert (4) 1½" Self-Drilling Stainless Steel Screws (H) into the posts to secure the Post Anchors (C).

• Repeat Steps 1-8 to assemble the other panel.

• Attempt to push the unit into the ground.
• Your screen panels can be rotated to hide the screws from one side.

• All 12" of Post Anchors (C) must be fully inserted.

• Hammer and switch posts every few taps.
• If using a hammer, make sure that you use a block of wood as to not damage the tops of the posts.

For Hard Ground: Soften soil with the claw side of a hammer and water, or use a cordless drill with a 1.5" diameter tulip auger.

• Dig a hole large enough to accommodate one post from each panel (approximately 8" in diameter and 12" deep.)
• Backfill and compact the dirt.

90° Degree Angle

180° Degree Angle

• Connect the 2 panels using (2) Joiners Clips (F) and (4) ¾" Self-Drilling Stainless Steel Screws (G).
• Units can be installed at a 90 degree or 180 degree layout (depending on your preferred install.)

• Email: support@encloscreens.com
• Phone: 704-892-5222 or 877-234-6196
• Text: 980-580-6508